Muscle Mustangs & Fast Fords
Ford Mustang DTS Drivetrain And Suspension - Project ProCharged Pony - Back Half for Your Blower
If you're going to forge ahead with your elapsed times, you best have an anvil that can take the beating.
Step By StepView Photo Gallery
Horsepower is a wonderful thing. It's the driving force that plants us in the seat and puts the smiles on our faces. These days, it's extremely easy to make gobs of pavement-buckling power, but the rest of the drivetrain may not be up to the task, especially with two or three times the stock power level passing through the crankshaft.
The 8.8's stock 28-spline axles are not what you want to depend on when your rig is making 400, 500, or 600 hp. With the right application of the clutch, even a stock engine can snap these axles like the toothpicks they are.
Our behind-the-scenes project car, a '90 Mustang GT that makes about 590 hp at the crank, has, until this point, gotten by with the stock rearend, even enduring aggressive drag radial and ET Street tire launches. Going down the track, we also realized the stock, 140,000-mile control arms were way overpowered and did not offer the rearend control we needed. As we fully plan to exploit the power provided by the supercharged, DSS-built 331, we called DTS Custom Service (a subsidiary of Drive Train Specialists) and asked about what we needed to put beneath our Pony.
"The majority of 8.8s, new or used, already have bent axle tubes," says Scott Marrison, general manager of DTS. "This has to do with the way the housing ends are installed at the factory, combined with the fact that the 8.8s are prone to axle twist." Thank the torque of the 5-liter for that.
We know plenty of racers, however, who for years have been using the 8.8 behind 1,200hp cars after they've been beefed up. And DTS knows a thing or two about making rearends survive at the track. It currently runs a car in the Edelbrock Pro Series Xtreme Street class (mid-eight-second e.t.'s are the norm), and has many customers who run in other equally fast and faster classes.
While our project car won't quite see that much power, its 590 ponies do require a capable rearend. One of the issues we encountered when using our own 8.8 was with the 2300K Cobra R disc brake kit that was installed on it. The kit employs SN-95-length axleshafts, which created a problem with the C-clip eliminator axles we wanted to use.
The axle-flange-to-housing-flange distance of 3.25 inches would not allow the pressed-on bearing to sit in the correct location. DTS modified a set of brake brackets from North Race Cars (Gladstone, Missouri) to work with its own billet 8.8 axle-tube ends to get that gap down to an acceptable 2.5 inches while maintaining the proper brake-caliper-bracket position. This allowed the use of a shorter/ stock-length axle.
The billet tube ends are similar to the Ford 9-inch design and retain the axle without the use of C-clips. These ends are welded on and utilize a tapered roller bearing. DTS uses the tapered roller bearings because the bearing presses into itself when cornering. This is beneficial to bearing longevity, and it also prevents leaks.
Once the axle tubes have been straightened and welded, support trusses are welded/bolted on. These are optional and should be considered if clutch drops loom in your future, as they further prevent the axle tubes from twisting or flexing.
With the DTS billet ends installed, the housing is then painted before the differential is dropped in. For our application, DTS used an Eaton Posi unit, which has been modified to accept DTS' forged spider gears for use with 33-spline axles. Mark Williams built the 33-spline axles that employ pressed-on wheel bearings to be used with the billet ends.
The Pro 5.0 3.55:1 ring-and-pinion set had been in our 8.8 only a few months, so we opted to reuse it. We also had DTS install a TA Performance main support cover, which it can offer to you as well.
To constrain our new axle, we contacted UPR Products for a set of new control arms. After mentioning our car's horsepower level, UPR sales associate and racer extra-ordinaire Jeremy Martorella recommended the company's Pro Series arms, which use aluminum and spherical rod-end bushings. He also sent us a set of UPR's urethane-bushed chrome-moly control arms, should the Pro Series pieces become too noisy for our street machine.
In addition, we ordered a set of UPR's Max-Cross subframe connectors, as our Pony was long overdue for a set, especially since we don't intend to put a rollbar in the car just yet.
Not all 8.8s are created equal, and if you're as horsepower hungry as we are, consider getting a quality-built piece such as the one we received from DTS. It's the only way you'll be sure to get all the enjoyment your high-horsepower Mustang can provide. Check out the captions to see what's involved in installing a high-performance back half for your blower.