Muscle Mustangs & Fast FordsProject Vehicles
1990 Ford Mustang GT ProCharger Install - Project ProCharged Pony - Blown, Stock & Born To Rock
Supercharging a stock 5.0L Mustang with help from Accessible Technologies, Inc.
For the 5.0L owner, there are a ton of ways to make easy horsepower and if we plan to hang with the current herd of Mustangs, supercharging is something we simply must do. Since MM&FF has two 5.0L naturally aspirated engine buildups completed or in the works, we looked to see how much power we could make with a blower.
Accessible Technologies, Inc. has been home to the ProCharger family of centrifugal superchargers since 1993, and is where we turned to unnaturally aspirate our Mustang GT. From boats to automobiles and motorcycles, there is a ProCharger for just about everything. Someone even used one to create a commercial airline de-icer, which works by simply blowing the ice off of the plane. Cool stuff for sure, and the diversity in which the product is used serves as additional research and development material for future versions of the ProCharger. But in our case, we simply want more power.
One of the reasons why we went with a ProCharger is because of the intercooler in its kits. When air is compressed, as in a supercharged application, the atoms bounce off of each other as they become more densely populated. This results in friction, and thus raises the temperature of the incoming air charge. ProCharger, and many turbocharged applications, use an intercooler to lower the air charge temperature by as much as 100 degrees, which in turn allows a more aggressive timing curve to be utilized in order to make additional power. Intercooled superchargers are less susceptible to powerfade, unlike non-intercooled systems. Ultimately, a cooler change means less chance of detonation and we're all about that.
There are generally two types of commonly used intercoolers, one is the air-to-air intercooler and the other an air-to-water intercooler. The air-to-air unit features a radiator-type cooler that uses passing air to cool the contents. An air-to-water unit circulates water around the intake charge to lower the temperature. Some racers will stuff ice into the water tank for additional efficiency to super cool a water-to-air intercooler.
The ProCharger we chose for our project is the P-1SC intercooled kit that fits Ford Mustangs from '86-93. The system is good up to 825 hp and can create boost levels of up to 30 psi. Using a radial impeller for a broad torque range, the head unit is capable of delivering 30 psi of boost and, with its CARB EO #D-365, the kit is 50-state legal and has up to 14 psi of boost. A 12-month warranty is standard, with an optional two-year extension available. For those who race, the P-1SC is legal for use in NMRA Real Street without the intercooler, but ATI offers the P-1SC-2 for use in that particular class, as the helixed impeller offers more high-rpm performance.
The SC in P-1SC stands for self-contained. As most centrifugal superchargers require tapping into the engine's oil supply to lubricate the internal transmission, the SC ProChargers come with their own internal oil supply system, which saves a few steps during installation and provides a cleaner overall installation. After a 500-mile break-in period, the fluid is changed, and the next interval is 6,000 miles. The oil is a 0-weight synthetic oil specifically designed for use in the high-speed environment of a supercharger. It also runs much cooler than engine oil, which has already been heated by the motor before going into the blower. Now that we have covered the supercharger we have chosen, let's go into a little detail on the application.
Our installation mule is a '90 Mustang GT equipped with a 5.0L engine and five-speed transmission. The car is well maintained, but has racked up 139,000 miles on the odometer. Modifications to the Mustang include an off-road X-pipe, Flowmaster two-chamber mufflers, a K&N filter and the "10-minute" tune-up. Baseline numbers for the filly came in at 202.2 rear-wheel horsepower and 275.6 lbs-ft of torque at the pony wheels. On the track, the GT posted a 14.45 at 96 mph and a 14.46 at 95.7 mph. Obviously, there is a better elapsed time to be had, but the 2.73 rear gear ratio is not exactly optimum for mercurial 60-foot times. We plan to remedy the ring-and-pinion situation later, but we'll need to return to the track with the supercharger and 2.73s for back-to-back comparison.
The ProCharger comes as a complete kit, with everything one would need to install this and head on down the road to better power and quicker elapsed times. Due to the high mileage of our engine, ATI recommended that we get a new set of fuel injectors to make sure we had equally rated injectors on all eight cylinders. After speaking with the folks at LaRocca's Performance, we opted for a set of 42-pound Ford Racing Performance Parts squirters. This was because the Mustang may see future engine modifications, thus requiring larger units. In using such large injectors right off the bat with our application, ATI recommended not using the supplied fuel management unit (FMU), as the injectors offered enough fuel for our power level, and a better idle quality would be had without using both of the items on our stock engine.
The injectors were sourced from Brothers Performance Warehouse in Corona, California. Brothers has just about any part you could want or need for your Mustang, so we gave a call for the injectors, as well as for a BBK adjustable billet fuel regulator, and a BBK in-tank 255-lph fuel pump. When going to a different flow-rated injector, it is important to have the mass air meter calibrated to the injectors. Brothers had a Pro-M Bullet 75mm meter calibrated to the 42-pound injectors and shipped it out to us.
Another fail-safe item is a good ignition system. We had recently given the Mustang a tune-up, save for spark plug wires, but seeing as the stock coil had over 100,000 miles on it, we opted to replace it with a Crane LX-92 high-performance coil. This was used with Crane's HI-6 CD ignition with rev limiter and timing retard. The HI-6 is a state-of-the-art, capacitive discharge-type ignition system that delivers up to 12 sparks to assure quick starting. Better spark is also required when cylinder pressure is increased, as in a supercharged or high-compression application.
Crane's HI-6 also comes with a staged rev limiter that can be set at up to 9,000 rpm in increments of 100 rpm. All HI-6 units can be equipped with the optional TRC-2, which is a timing retard control module. This is set with the knob on the module and retards the timing in proportion to boost levels. In keeping with the Crane ignition theme, we opted for a set of its 8.5mm Fire Wire spark plug wires. These offer a low 25 ohm-per-foot resistance and transmit up to 50 percent more energy to the spark plugs than other performance wires. The FireWires use a "reactive core" to filter out RFI and EMI noise, which keeps your radio clear and protects your computer. They also have 550-degree boots for that hot environment between the headers.