Mark Houlahan
Tech Editor, Mustang Monthly
January 10, 2014

Completing a late-model EFI engine swap is challenging enough without taking wiring into consideration, and while the wiring aspect of the swap is usually one of the last things people think of, it is one of the first things that should be figured out before you grab the first wrench. A bargain of an engine find might turn out to be not so much of a bargain if you can't source the proper wiring for the engine to make it run. While the go-to engine right now might be the 4.6L Four-Valve "Coyote" engine found in the '11-'14 Mustang GT (and available through Ford Racing's crate engine program), there are plenty of Ford engine offerings sitting in salvage yards (and possibly in your own backyard) that would make for a great engine swap into a classic Mustang or Ford.

Just such an example can be found between the front fenders of the '68 Mustang coupe seen here at Gillis Performance Restorations (GPR). Rusty Gillis is the man behind this project, and while the aforementioned Coyote would certainly be a welcome addition to this tidy little coupe, it is a budget shop project mainly being built from cast off items to offer a rolling business card of GPR's paint and body abilities. Since the body and paint are the main focus, the drivetrain consideration for the project basically fell into the realm of cheap and reliable, with EFI, and an overdrive trans to make it a nice cruiser. Rusty didn't need 500 horsepower to show off his shop's paint and metal working skills. To that end, he just happened to have a '96 Thunderbird sitting behind the shop that used to be his father's daily driver. The 4.6L Two-Valve engine under the hood would be the perfect swap candidate—low mileage, reliable, fuel injected, and best of all, free!

The panel-based wiring concept preached by the Ron Francis folks means anyone, even Rusty, can wire his/her EFI engine project quickly and easily.

Tackling the 4.6L Two-Valve's physical installation would be a breeze for the likes of Rusty and his shop, however, the wiring was a different story altogether.

"I'm an old school carburetor guy; EFI wiring scares me," Rusty explained to us. It's good news for Rusty then that we know EFI wiring and live and breathe these swaps here at Modified Mustangs & Fords. While the Three-Valve modular in our Generation Gap project and Four-Valve Coyote modular in our Colt of Personality project both are/will be wired via Ford Racing Control Pack wiring kits, older Four-Valve and Two-Valve modulars, and more obscure swap candidates like the 3.8L supercharged V-6 from the Thunderbird Super Coupe, the 2.3L turbocharged I-4 from the Thunderbird Turbo Coupe and Mustang SVO, and other Ford engine packages can be a little more challenging to wire. However, if you're smart, you'll pick up the phone and order a Telorvek wiring panel system from The Detail Zone, a division of Ron Francis Wiring.

1. Depending upon the system and options ordered, the panel ships with prepackaged wiring components that are numerically labeled. It makes it super easy, as the instructions tell you which bag to grab next.
2. We caution not to open all of the bags at once, as some sensors use the same connector. However, we did open one package to show the quality of the hardware included. The connector shells are all brand new and correct for the sensor/application, and the wire is printed with the circuit and terminal number for easy connection.
3. When using a system like this, it is critical to determine your panel location first, with wire routing a secondary, but still important consideration. Rusty decided on the right rear trunk area. A trunk block-off panel will be fabricated with the wiring panel mounted on the back of it as mocked up here.
4. It may be a little hard to determine the panel size by photos, so we offer to you this photo showing measurements of the panel itself, which are 12x6.5 inches and roughly about 3 inches tall. Don’t forget you’ll need room to mount the PCM nearby as well.
5. In the case of the 4.6L Rusty installed from his father’s T-bird, the original plan was to utilize the stock wiring. As such, the old harness needs to be removed from the engine before we can get started.
6. An important step before routing a single wire is determining where your engine and transmission wiring will enter the vehicle en route to the wiring panel. Rusty’s ’68 coupe did not have A/C or chassis wiring installed yet, so it took a little careful measuring before drilling, but a hole was cut just behind the passenger hood hinge in the upper cowl panel for the wire bundle to pass through. Always use a wire grommet for any wires that pass through a metal panel.
7. Once the ’68’s panel location and main wire routing had been confirmed, it was time to get under way with the first bag of wires/connections, which is the wiring for the fuel injectors. Following the well-written instructions, the first injector for each bank is identified and the remaining connectors line up/fall into place with each remaining injector.
8. After routing the injector wiring through the firewall grommet and toward the rear of the car, it was decided to “pre-stage” each wiring bag on its input/output device. Seen here are the wire bundles for the coil packs, MAF sensor, throttle position, and more plugged in and ready to be routed.
9. Routing these bundles of wires rearward on the engine while following the initial run from the fuel injectors makes it easy to bundle the wiring together. For now, we’re using “sacrificial” tie-wraps to keep things neat and Rusty will be covering the wiring with split loom later, once the chassis wiring and any other wiring is integrated into the vehicle.
10. As bundles of wires are unrolled and routed rearward, we ended up with two distinct wire bundles to pass through the firewall grommet. The wiring you see here at this stage is strictly from engine mounted sensors/actuators.
11. After passing through the firewall grommet, the wiring was kept in a neat rearward trail to prevent the wiring from tangling. At this point, we weren’t sure if we were going to run the wiring on the floor pan or through the sill plate area.
12. The wiring includes the OBD-II service port, which is to be mounted in an easily accessible location near the driver. In new cars, you will usually find this connector at the base of the dashboard. This connector will allow easy servicing by any Ford dealer or tuning shop that needs access to the PCM for calibration/tuning operations.