Chick Key
July 1, 2008

Step By Step

View Photo Gallery
Mdmp_0807_01_z 1965_ford_mustang_fastback Mdmp_0807_02_z 1965_ford_mustang_fastback Mdmp_0807_03_z 1965_ford_mustang_fastback Mdmp_0807_04_z 1965_ford_mustang_fastback Mdmp_0807_05_z 1965_ford_mustang_fastback Mdmp_0807_06_z 1965_ford_mustang_fastback Mdmp_0807_07_z 1965_ford_mustang_fastback Mdmp_0807_08_z 1965_ford_mustang_fastback

It's the quiet ones you have to worry about. You think they're at their desks looking at spreadsheets and being good pencil pushers, then you find out they've really been planning total domination.

In the case of mild-mannered Dale Irwin of Van Buren, Indiana, his plot centered on a certain '65 Mustang fastback and building it into an after-dark street predator. As it turns out, Dale has a talent not only as a desk jockey, but also as an automotive engineer. The real story of his car isn't the long list of trick parts installed on it, but what he did with those parts to set this car off from the rest of the street-machine genre.

Dale began with the look he wanted-a clean exterior highlighted by a set of Maier Racing fender flares to allow big patches of vulcanized Goodyear Eagle F1 rubber to reside inside. From there, he went where most car builds should, chassis and handling. Dale cabbaged on to an independent rear suspension system from the venerable '00 Cobra R racing program, complete with 3.55 Gerodisc posi and 31-spline axles. Up front, a complete Chris Alston coilover tubular front suspension and Stainless Steel Brakes' Force 10 disc conversion were chosen to handle the soon-to-be-added horsepower. That's about as far as the build got before Dale's inner engineer took over.

He started with a DVS Restorations IRS installation kit and heavily modified both the kit and the car to accept the massive 17x11-inch Vintage Wheel Works Vintage 45 rims. With some help from the machining experts at Jennerjahn Machine, he reengineered the mounting and even removed the spring perch from the lower control arms for a much smoother install.

About this time, Dale found a deal on an '03 Mustang GT 4.6 2V engine and 4R70W with less than 10 miles on them. Mounting the wide motor in the '65 chassis meant his TCP goodies wouldn't fit in the front as planned, so he began reengineering the front suspension and moved it out to allow for the wider motor to sit down in the engine bay of the '65. This required Dale to design his own shock towers and weld them in place. At the same time, he custom engineered his own power rack-and-pinion system that not only worked with his original spindles, but also allowed for a better turning radius. Careful engineering allowed Dale to improve the car's roll center and all but eliminate bumpsteer.

Boost Is Good
With the 4.6 engine in place, Dale got to work getting it ready to provide horsepower to the big rear tires. First, an Eaton M90 supercharger was installed on the less-than-10-mile motor. Then there was a trip to Danville, Illinois, to see Brad Edington with Total Performance for an ACCEL Gen 7 computer, dual Walbro electric fuel pumps, a set of 42-lb/hr injectors, and Aeromotive fuel rails. The exhaust is handled by a set of Ford Racing Performance Parts shorty headers, Flowmaster mufflers, and a custom 21/2-inch aluminized exhaust system exiting the original GT trumpet holes.

A Baumann Engineering electronic transmission controller was employed to provide computer shifting duties. The '65's chassis allowed Dale a little engineering convenience as well. He built some custom cages for the torque box area that not only strengthen the chassis, but also hold a pair of Derale coolers with electric fans-one for the transmission and one for the intercooler. McCoarts' Auto in {{{Somerset}}}, Indiana, custom plumbed the late-model hydroboost system and brakes. Dale custom engineered the three-point chassis brace to fit the new go-fast goodies residing underhood.