Matt Stone
March 26, 2014
Photos By: Drew Phillips

For any build to look right, stance is critical, and Williams and EBMC really nailed the look and maximized the handling potential with another well thought out and executed smorgasbord of factory and aftermarket suspension design and upgrades, plus just the right rolling stock. The frame is beefed up and tied together with Heidts weld-in subframe connectors, not to mention some serious structural triangulation and stiffening going on under hood with Total Control Products' Heim-jointed adjustable shock tower and firewall braces; all in satin and black finish to keep bling under control and underscore the whole car's stealthy black/titanium theme. Total also supplied the rest of the front suspension including upper and lower control arms. The shocks up front are Ridetech coilovers with QA1s out back. The rearend gets a 2-inch leaf drop; Borgeson supplies the quick-ratio steering box and Wilwood the large and high-tech, four-wheel disc brakes. Again keeping that stance taut and just right are slightly staggered rolling stock, with 18x8-inch Boze rims out back with 17x7s up front; all wrapped in BFG performance tires.

In case you haven't figured it out by now, the detailing on every square millimeter of this car is spectacular. It's street driven to be sure, but show quality all the way. Nowhere is this more obvious than the interior. The not-too-shiny black theme continues inside, and you'll still recognize the basics as Gen I Mustang, but it's been evolved a long way from those early ponies. The main instrumentation is new Vintage stepped down gauges in a custom molded bezel, approximating the original IP's look and layout. Just about everything else is wrapped in super soft yummy looking black leather. The door panels are custom molded in a more modern design, with power windows added. The seats are Corbeau GTS II chairs, customized a bit and wrapped in the same leather as everything else. The old floor pedal style E-brake has been dumped in favor of a sportier tunnel-mounted handbrake just aft of the shifter. The trunk benefits from much the same look, covered in the same carpeting as the cabin. The thumping audio system is a combination of Pioneer, Polk Audio, and Kicker components. And a Ron Francis Wireworks custom electrical harness ties it all together.

Williams' Mustang is a shining example of clever and tasteful thought, good planning and high quality execution. It appears to be a textbook lesson in component matching and superlative workmanship. It doesn't matter if you're doing a '65 coupe or a 2014 Shelby, just conceive, plan and execute it to this level, and you'll have something very special to drive and look at. Job well done.

The Details
Clarence Williams '65 Mustang coupe
347ci small-block V-8
Iron block, two-bolt mains
4.040-inch bore
3.4-inch stroke
Cast steel crankshaft
I-beam Ford 5.4-inch connecting rods
Hypereutectic flat-top pistons with Hastings rings.
Ford Racing aluminum 62cc X heads, hand ported, 1.94-inch intake/1.54-inch exhaust valves, port-matched
1.6:1 roller rocker arms
Ford Racing M-6250-E303 cam, 220-degree lift at 0.050 duration
Edelbrock Air Gap aluminum intake manifold
FAST throttle body fuel injection
MSD billet distributor
10:1 compression ratio
400 hp/380 lb-ft of torque
JBA headers
TIG-welded custom 2.5-inch exhaust by East Bay Muscle Cars
MagnaFlow mufflers
Ford 4R70W four-speed automatic
OptiShift trans control system
2,400 stall speed torque converter
Lokar shifter
Ford 9-inch
Motive 3.89:1 gears
Limited-slip differential
Front: Total Control Products upper and lower control arms with coilover conversion; Ridetech shocks
Rear: High performance leaf springs with 2-inch drop, QA1 billet shocks
Quick-ratio Borgeson power steering box
Brakes Front: Wilwood disc, 12.19-inch cross-drilled rotors
Rear: Wilwood disc, 12.19-inch cross-drilled rotors
Wilwood dual master cylinder and adjustable proportioning valve
EBMC custom nickel copper brake lines
Wheels Front: Boze Pro Touring, 17x7
Rear: Boze, Pro Touring, 18x8
Front: BFG KDW2, P225/45ZR17
Rear: BFG KDW2, 255/40ZR18
New Vintage gauges in custom bezels; custom-molded door panels; black leather Corbeau GTS II bucket seats; Flaming River tilt column and wheel; Lokar shifter, tunnel-mounted handbrake lever; Pioneer/Polk Audio/Kicker entertainment system
Rolled wheelwells; smoothed and modified firewall and engine compartment; stock hood with '69 Mach I 'scoop; smoothed and body painted front and rear bumpers; powdercoated window trim; trunk-mounted Braille battery; bullet rearview mirrors; Hotchkis billet hoodpin kit; EBMC-modified taillight bezels; two-stage matte Black/titanium paint